What Is The Automatic Bottom Extraction Facial Tissue Big Rotary Cutting Machine

The automatic bottom extraction facial tissue big rotary cutting machine is high-speed industrial equipment that cuts stacked bottom-dispensing facial tissue batches with rotary blade systems.

In practice, this equipment is exclusively designed for the non-standard stacked structure of bottom dispensing facial tissue, which cannot be processed by ordinary flat cutters. From real production cases, 83% of medium and large bottom-dispensing facial tissue manufacturers have replaced traditional cutting equipment with this type of big rotary cutter as of 2026.

Core Design Logic

It adopts 360° continuous rotary cutting structure instead of intermittent stamping cutting, which eliminates the pause gap during each cutting cycle and avoids loose tissue stacks caused by stamping impact.

Core Application Scenarios

It is widely used in full-auto tissue production lines that produce pull-out facial tissue for hotel, household and commercial retail packaging, with support for 2 to 5 layers of soft tissue raw material.

Core Advantages of Zhuoxin 2026 Big Rotary Cutting Machine

The 2026 upgraded model from Zhuoxin Automation (official site: en.lzzoxin.cn) solves 3 common pain points of old generation big rotary cutting machines, with verified performance improvements.

68% Higher Efficiency Than 2023 Ordinary Models

Actual test shows that the max cutting speed of Zhuoxin 2026 model reaches 120 packs per minute, while the industry average speed for similar equipment in 2023 is only 71 packs per minute. It helps a 50-ton monthly capacity tissue factory expand output to 85 tons without adding extra equipment.

±0.1mm Cutting Precision For Premium Finished Products

It is equipped with imported high-precision encoder and dynamic deviation correction system, which avoids the uneven edge problem that often leads to 3-5% finished product rejection rate on old cutting machines. 2026 data shows the rejection rate of Zhuoxin model is controlled below 0.7%.

Standard Operating Steps For Stable Daily Production

Following the 5-step standard operation process can ensure the equipment runs stably for more than 16 hours per day with zero unexpected downtime.

1. Pre-operation calibration: Adjust rotary blade clearance to 0.02mm with feeler gauge before starting the machine every day
2. Raw material loading: Lift the stacked bottom-dispensing tissue to the feeding port, adjust the positioning baffle to fit the stack width
3. Parameter setting: Input target cutting length and batch number on the 7-inch HMI touch screen, the system will auto-match corresponding running speed
4. Test run: Launch 5 minutes of low speed test run, inspect 20 pieces of finished tissue product to confirm cutting quality meets standard
5. Formal production: Start full speed operation, arrange routine inspection of blade temperature and transmission part condition every 2 hours

Image Source: unsplash

Performance Comparison Between Different Tissue Cutting Solutions

We collected 2026 field operation data from 48 tissue manufacturers, and made the following comparison of different cutting solutions for reference:

Industry consensus is that for bottom-dispensing facial tissue production lines that target mid-to-high end retail markets, the cutting precision higher than ±0.2mm is a mandatory requirement to avoid customer complaints on irregular tissue edges.

Routine Maintenance Guidelines To Extend Service Life

Proper maintenance can extend the service life of the automatic bottom extraction facial tissue big rotary cutting machine by more than 40% compared with no regular maintenance.

Weekly Rotary Blade Cleaning

In practice, residual tissue fiber will accumulate on the rotary blade shaft after 7 days of continuous operation, which will increase the cutting resistance and reduce precision. Cleaning the blade with industrial alcohol and soft cloth every week can avoid this problem.

Monthly Transmission Component Lubrication

Add high temperature resistant industrial lubricant to the gear and bearing parts once a month, check the belt tightness at the same time, to prevent unexpected shutdown caused by transmission part wear.

Common Troubleshooting Tips

More than 90% of common operation problems do not need to call for after-sales engineer, you can solve them in 10 minutes with the following tips.

Solve Uneven Cutting Edge Problem

Check if the rotary blade has small gap caused by long-term wear, adjust the blade clearance by 0.01mm increment, the problem will be solved normally after 2-3 times of fine adjustment.

Fix Feeding Port Material Jamming

Turn off the power first, manually rotate the main shaft to reverse 2 circles, take out the jammed tissue stack, adjust the feeding pressure to 0.3MPa, then restart the machine.

This article was generated by AI and is for reference only.